Home / Cabinet hardware / Hinges & soft-close
Hinges and the soft-close system, on the wall.
A hinge is the one fitting nobody watches working, which is exactly why it is the first thing to be cut for cost - and the first thing to show. This page is the closing wall in our Foshan showroom: the cup hinges on their adjustment boards, the clip-on and undermount variants, the flap stays and the gas struts for the lift-up panels, each class rated and photographed in the state it ships in.
The closing system
Soft-close is the default, not the upgrade.
The hinges above are the standard class on the wall: soft-close as fitted, the damper integral to the hinge rather than bolted on afterwards, rated at 50,000 open-close cycles, with the mounting plate sized so a door can be swapped without chasing screw holes. The last few centimetres of the door's travel are what the damper owns - that is the difference between a door that closes quietly for a decade and one that starts knocking in year two - and the rating is not a brochure number here, because every door is cycled at the factory before the box is wrapped.
- HingesSoft-close, rated at 50,000 cycles - DTC on request
- Door loadSingle door up to 28 kg; hinge count and plate follow
- VariantsStandard cup, clip-on, undermount, push-open - on the wall
- Lift-upFlap stays and gas struts, sized to the panel weight
- Board18 mm E0 plywood, ≤0.05 mg/m³ (GB/T 39600, report SQ2405393) - certificates
- MOQMixed orders from 1,500 sq ft - no minimum at the sample stage
- Lead10-14 days factory; DDP 18-22 US West, 32-40 US East, 15-20 Sydney
- Warranty5-year hardware warranty, aligned with the fitting manufacturer’s
The wall carries the full closing family, not the standard cup hinge alone: the clip-on and undermount variants on their own boards, the flap stays and the gas struts for the lift-up panels, and the push-open units that sit where a handle would. Everything on it runs the same rating discipline as the runners - the number is written per fitting on the spec sheet, the 28 kg single-door load sets the hinge count and the plate size, and the 5-year warranty covers the class, the damper and the plate as one line.
Cup hinges
The adjustment screws, visible before the door goes on.
The case on the left holds the hinge family in both metals - the brass set and the matte black set, the lids open on the glass shelves, so the cup, the arm and the damper can be read at the same time. The board at the right is the standard cup hinge on its clear panel, and it is photographed the way an installer will see it: the adjustment screws out, the mounting plate on show, because height, depth and pressure are adjusted in place, and a hinge that adjusts with the door on is a hinge that never needs a new fitting to keep the line straight.
The clip-on variant runs on the same board family next to it - the hinge that clips onto the door edge for the runs where a drilled cup is not the answer - and the undermount sits on the concealed line for the glass-front bays. Each class is rated at the same 50,000 cycles, and each is cycled at the factory before it ships, which is why the rating on the spec sheet reads as one number for the family rather than a table of exceptions. The damper is integral to every class on the wall; the soft-close is not the upgrade on this line.


Clip-on & undermount
Two more ways the door hangs on the same rating.
The clip-on hinge above is the class for the edge-mounted runs: the brushed steel arm clips to the door edge rather than into a bored cup, which is what makes it the answer for the glass doors, the framed fronts and the retrofits where the carcass is already cut. It is photographed on its own clear panel at the angle the installer works from, the arm, the clip and the damper in the same frame, and it is rated at the same 50,000 cycles as the standard cup - the variant changes how the door hangs, not how long it is allowed to.
The undermount sits on the concealed line for the glass-front bays, where the hinge has to stay out of sight from the front and the side at the same time. Both classes run the 28 kg door-load logic the production list uses: the hinge count and the plate size follow the door weight, so a heavy painted slab or a full-glass door gets its hinge arithmetic before it is hung, not after the first month of drift. Both are cycled at the factory, both are itemised per fitting on the spec sheet, and both carry the 5-year warranty as part of the closing family rather than as a separate line.
Lift-up & flap
The panels that open on struts, sized to the weight.
The board on the left is the lift-up family in its working set: the gas struts in silver and white, the flap stays, the lid supports, and the small hinge sets along the bottom of the board - the hardware that owns every panel that opens on anything other than a hinged door. The struts are sized to the panel weight rather than to a catalogue length, which is the discipline that keeps a lift-up panel holding at the top of its travel at year five the way it did on the showroom floor, and the sizing calculation goes on the spec sheet with the panel it serves.
The flap stays run the smaller jobs - the cabinet door that lifts on the counter, the appliance panel, the service door - and they sit on the same board as the struts because the decision is the same one: the weight of the panel sets the fitting, and the fitting is rated and photographed before it is cut into the program. Every unit on the board is cycled at the factory in the state it ships in, the way the cup hinges are, so the 50,000-cycle standard reads across the whole closing family - door, flap, lift-up - as one line on the spec sheet, warrantied for five years.
FAQ
Hinges and soft-close, in plain answers.
Are soft-close hinges standard on every collection?
What does the 50,000-cycle rating actually cover?
How heavy can a single door be on the standard hinges?
What happens when a hinge starts to drop or bind?
Can you fit a specific hinge class to our spec?
Can I see the hinge wall before I order?
For specifiers
Specifying a closing program, not a kitchen?
Volume pricing, OEM/ODM hinge classes and a hardware sample kit - the dealer line answers in your time zone.
Every hinge, rated before the door goes on.
Send the door weights and the finish list - the closing system is written into the quote per door, with the cycle rating it ships under.