Home / Cabinet hardware / Display boards & sample walls
The sample walls the program is drawn from.
Every finish, fitting and front on a spec sheet starts on a board: the chip wall with the finishes side by side, the fitting panel with the hardware in its rows, the front wall with the doors in their grain. This page is the display line in our Foshan showroom - the sample boards, the fitting panels and the finish walls - photographed the way a program is decided against them.
The display line
The boards the program is drawn from.
The boards on the wall above are the display line in its working state: the small hardware set in its rows behind the counter glass - the clips and the pins, the coloured plastic and the metal, in the order the board keeps them. A sample board is the surface a program is drawn from, and the photo is the board in the state it is used in, with the decisions made against it visible in the layout. What a board carries is not decoration - it is the element the spec sheet lists, set in the position it will ship in.
- ChipsWood, laminate and finish samples, cut to the board
- FittingsFlap, hinge and clip hardware in their rows
- FrontsThe grain and edge-banding wall the doors are drawn from
- HandlesThe aluminium range on the grid, with the inserts
- Board18 mm E0 plywood, ≤0.05 mg/m³ (GB/T 39600, report SQ2405393) - certificates
- MOQMixed orders from 1,500 sq ft - no minimum at the sample stage
- Lead10-14 days factory; DDP 18-22 US West, 32-40 US East, 15-20 Sydney
- Warranty5-year hardware warranty, aligned with the fitting manufacturer’s
The line runs around that board into the walls the showroom keeps: the dark board with the finish chips and the flap and hinge fittings in their columns, the grey grid with the aluminium handles and the drawer inserts, the white panels with the small fittings in their rows, and the wall of the wood-grain fronts with the edge banding and the profiles in their runs. Every element on the line is the element a spec sheet carries - the chip is the finish, the fitting is the hardware, the front is the door - and every element is photographed in the state the showroom keeps it, because a sample that reads well on a card and wrong on the wall is the failure the display line exists to catch.
The chip boards
The finish beside the fitting, the grid beside the front.
The dark board on the left is the chip wall in its working set: the wood and the laminate chips cut into their columns, the metal flap and hinge fittings running down the board in the same columns, so the finish and the fitting that carry it are decided in one look rather than in two visits. The grey board on the right is the grid a layout is drawn on: the aluminium handles in their rows, the corner boxes and the drawer inserts mounted to the board, the wood-tone shelves running beneath it - the handle against the front, the insert against the corner box, everything in the position it ships in.
The boards are the surfaces the program is decided on, and they are photographed with the mounts in place, because a decision made on a board is a decision the spec sheet can carry: the chip is the finish, the fitting is the hardware, the handle is the front's line, and the reference for each is written from the board, not from a catalogue. The two boards are the standard the production line draws from, and a program that is laid out on them is itemised the way it is laid out - element by element, with the board behind it in the showroom.


The small fittings
The parts kept in the order a swap needs them.
The panels on the left carry the small end of the hardware line: the clips, the pins and the small metal fittings laid in their rows on the white panels, each in the position the board keeps it. The small fittings are the parts that make a replacement a five-minute job at the site instead of a callback - the clip that holds the shelf, the pin that takes the weight, the connector that closes the corner - and the panels keep them in the order a swap needs them, per door, per drawer, per corner, the way the fastener wall on the hardware page does.
They are the standard hardware the cabinets ship with, not an upgrade line, and they are photographed on the wall the way the rest of the display line is, in the state a program is decided against them. The reference for each fitting is on the spec sheet with the cabinet it serves, so the spare that ships with a container is the part the board shows, and the swap at the site is made against the same material the program was drawn from.
The finish wall
The grain, the edge and the profile, in their rows.
The wall on the left is the finish range in its working state: the wood-grain drawer fronts stacked in their rows, the shelf-edge samples running with them, the edge banding and the slim aluminium profiles in the same run. The wall is the surface a finish is decided on - the grain against the grain, the edge against the edge, the profile against the front it bands - and it is photographed in the rows the showroom keeps, because a finish is chosen against its neighbours, not from a card held at arm's length.
The chips on the boards from the section above are cut from this wall, which is the discipline the display line runs: the sample a program is drawn from is the sample the production line builds from, and the two are photographed together so the decision and the build are made on the same material. The edge banding and the profiles are the detail a finish holds together, and they carry the same reference on the spec sheet as the front they sit on. When a program is decided, the wall is where it is decided, and the spec sheet is where it is written - the element on the board is the element on the sheet, and the 5-year warranty covers them as the lines they are.
FAQ
Display boards, in plain answers.
What are the display boards and sample walls used for?
Can a sample board be built to our layout?
Do the finish chips match the production panels?
Are the small fittings on the panels included in the standard?
What happens if a fitting on the board wears at the site?
Can I see the sample walls before I order?
For specifiers
Specifying a sample program, not a kitchen?
Volume pricing, OEM/ODM board builds and a sample kit - the dealer line answers in your time zone.
Every element on the board, on the spec sheet.
Send the finishes, the fittings and the fronts - the display line is written into the quote as the program is drawn from it.